How To Change A Brake Light In A Hyundai Elantra

Hyundai Elantra Tail Light Bulbs Replacement Guide
How to change a burnt out brake, rear plow signal or side marking light bulb in a sixth generation 2017 to 2020 Elantra.

2018 Elantra Tail Lights
Open up Torso Lid
Fabric Access Cover This automotive maintenance tutorial was specifically written to aid owners of the 6th generation (2017, 2018, 2019, 2020 and maybe also the 2021 model year) Hyundai Elantra sedan in changing a burnt out brake, rear turn signal or side marking light bulb in the tail low-cal housings (or upgrading them to brighter LED units).

Owners of other Hyundai, Genesis or Kia vehicles such as the Sonata, Accent, Veloster, Ioniq, Kona, Nexo, Venue, Tucson, Santa Fe, Palisade, G70, G80, G90, Soul, Sportage, Niro, Sorento, Telluride, Rio, Forte, Optima, Stinger, Cadenza, K900, Sedona and Seltos may also find these DIY instructions to be helpful.

The compatible replacement light bulb part numbers are as follows: Restriction # P21/5W (also known equally 7528), Rear Turn Betoken # 1156A or 1156NA (Amber) and Rear Side Marker # 2825 (also known as W5W).

If you would like to have brighter tail lights, install some P21/5W LED, 1156A LED and 2825 LED bulbs.

The tools needed to remove the tail lite housing in society to access and replace the bulbs include a 10mm socket with a i/4" drive ratchet or a 10mm wrench and perchance a plastic pry bar tool.

The start 2 steps are to open the trunk chapeau and and so move to the side of the car with the burnt out light seedling.

(If you need to replace the bulbs in the trunk lid housing, check out the 2017-2020 Hyundai Elantra Contrary & Parking Calorie-free Bulbs Replacement Guide.)

Wait within the body and locate the rectangular shaped material access encompass fastened to the cargo expanse liner just in front of the tail light housing.

Pull Out Access Console
Locate Two Nuts
Loosen Counterclockwise Gently pull the access cover out of the cargo surface area liner.

Locate the two modest basics that secure the tail light housing to the rear corner of the vehicle.

Loosen the nuts by turning them in the counterclockwise management with a 10mm socket and a 1/4" drive ratchet.

I found that using a short extension bar fabricated it easier to loosen the nuts.

(On some model years, the 2 basics may require an 8mm socket instead of a 10mm socket.)

Remove Second Nut
Spin Off By Mitt
Two Basics Removed Spin off the two basics the rest of the way past hand to prevent them from falling down into the rear bumper cover.

Set the 2 nuts bated in a rubber identify.

Pull Housing Off Car
Tap To Loosen 2 Pegs
Low-cal Housing Removed Advisedly pull the tail light housing straight off the rear corner of the vehicle.

The tail light housing is withal held in identify by 2 pegs inserted into plastic grommets and a slot fastened to the button head of a plastic pop rivet.

If you have trouble loosening the friction fasteners, use a hammer or the handle of a screwdriver to tap on the pegs from inside the cargo expanse.

Y'all can also use a plastic pry bar tool to very carefully and gently pry forth the outer edge of the tail light housing. Avoid using excessive force to forbid from smashing the lens encompass.

In one case you loosen the friction fasteners, slide the tail lite housing straight off the rear corner of the vehicle.

Disconnect Power Plug
Rear Corner of Vehicle
Back Side of Housing Push in the release tab on the electrical connector inside the trunk before sliding the power plug straight out of its socket.

Gently remove the rubber grommet and the electrical connector from the hole behind the tail calorie-free housing.

Set the tail low-cal housing down on a soft surface such equally within the body to prevent from scratching the lens embrace.

Brake Lite Bulb Socket
Push button Down & one/iv Turn CC
Install New Light Bulb The big greyness plastic seedling socket contains the brake (stop lamp) low-cal bulb.

Rotate the seedling socket 1/four plough in the counterclockwise direction before pulling it direct out of the housing.

Push the old bulb down into the socket and rotate it ane/4 plow in the counterclockwise direction before pulling it straight out.

Push a new bayonet style number P21/5W light bulb downward into the socket and rotate information technology ane/4 turn in the clockwise direction to secure information technology into identify.

If you would similar to take brighter brake lights, install some compatible replacement P21/5W LED bulbs.

1/4 Turn Clockwise - Lock
Rear Plough Signal Light
Push button Downwards 1/4 Plough CC Re-insert the restriction light seedling socket dorsum into the housing and rotate information technology 1/4 plow in the clockwise direction to secure it into place.

The orange plastic seedling socket contains the rear turn bespeak calorie-free bulb.

Rotate the bulb socket 1/iv turn in the counterclockwise direction before pulling it straight out of the housing.

Push the old light seedling down into the socket and rotate information technology 1/4 turn in the counterclockwise management before pulling it straight out of the socket.

Install New Plough Signal
1/iv Turn Clockwise - Lock
Rear Side Marking Bulb Push button a new bayonet way number 1156A amber colored light bulb down into the socket and rotate it 1/4 turn in the clockwise management to secure information technology into place.

If you would similar to take brighter rear plow signal lights, install some compatible replacement 1156A LED bulbs.

Re-insert the rear turn point lite seedling socket into the housing and rotate it 1/4 turn in the clockwise direction to secure it into place.

The small-scale bulb socket on the outer corner of the light housing contains the rear side marker bulb.

Rotate the seedling socket 1/4 plow in the counterclockwise direction before pulling information technology directly out of the housing.

Pull Out Old Light Bulb
Push In New Light Seedling
1/iv Plow Clockwise - Lock Pull the former light seedling direct out of the socket.

Push a new miniature wedge base number 2825 light bulb directly into the socket.

If you would like to have brighter rear side marker lights that will also concluding a lot longer before called-for out, install some uniform replacement 2825 LED bulbs.

Re-insert the seedling socket into the housing and rotate it one/four plough in the clockwise direction to secure it into place.

Insert Plug & Wires
Line Up Slot & Popular Rivet
Line Up two Pegs & Holes Concur the tail light housing near the rear corner of the vehicle.

Insert the electric connector through the opening in the sheet metal and through to the cargo area.

Secure the prophylactic grommet on the wiring loom to the opening in the sheet metal to keep rain h2o from entering the cargo area.

Line upwardly the slot and two pegs on the rear of the tail light housing with the pop rivet button head and the ii small holes on the rear corner of the vehicle.

Secure Safe Grommet
Slide On Tail Light Housing
Push In Ability Plug Carefully slide the tail light housing back into place on the rear corner of the automobile.

Move to the inside of the trunk.

Button the electric connector straight into the socket until yous hear or experience information technology "click" deeply into place.

Spin On 2 Basics
Tighten Clockwise Spin on the 2 basics a few turns past mitt in the clockwise direction.

Tighten the two nuts in the clockwise direction with the 10mm socket and a 1/iv" drive ratchet until they are snug.

(Some model years may be equipped with 8mm nuts instead of 10mm fasteners.)

Try to avoid over tightening the nuts to forbid from cracking the plastic tail light housing.

Supervene upon Access Embrace
Access Cover Secured
Test New Tail Calorie-free Bulbs Push button the cloth admission cover back into place on the carpeted trunk liner.

To test the new tail light bulbs, take an assistant stride on the brake pedal, turn on the parking lights and activate the hazard signals.

Cheque out my 2017-2020 Hyundai Elantra Opposite & Parking Light Bulbs Replacement Guide if you demand to change those bulbs in the low-cal housing attached to the trunk hat.

For more, please check out all of my 2017-2020 Hyundai Elantra DIY Repair & Maintenance Guides.

Source: https://paulstravelpictures.com/2017-2020-Hyundai-Elantra-Tail-Light-Bulbs-Replacement-Guide/index.html

Posted by: pageothessonce.blogspot.com