How Do You Change A Bathroom Sink Faucet

Download Commodity

A new faucet is a great style to update your bathroom and give it a whole new look. Whether you are renovating the bathroom or demand to replace an onetime or leaky faucet, this is a relatively simple DIY project that you can achieve in a few hours. The important affair is to get a faucet that fits your sink, and then you should remove the original faucet earlier purchasing a replacement.

1
Gather your tools and supplies. Replacing a bathroom faucet is a straightforward job, but information technology does require a few tools that you'll need to remove the former faucet and install the new one. The tools you'll need include:^[1]
- Adjustable wrench
- Basin wrench
- Bucket
- Towel
- Flashlight
- Measuring tape
- Plumber's tape
- Sponge or scrubber
- Bathroom cleaner or soap
- Rag or cloth
- New faucet (purchased after you lot remove the original)
2
Prepare your work area. Remove everything from underneath the sink. Place a towel beneath the pipes to protect the vanity from water damage. Place a bucket over the towel and under the faucet to catch any water that drips down.
- You tin also lay a garbage pocketbook down under the towel for even more protection, or in place of the saucepan.
Advertizement
3
Turn off the water. Locate the h2o shutoff valve for the bathroom sink. It should be nether the sink, within the vanity. Plough the valve to the right (clockwise) to close the valve and shut off the water to the faucet.^[2]
- Depending on your plumbing, you may have a single water valve for the unabridged faucet, or you lot may have ii separate valves for the hot and cold h2o.
- If you have problem locating the shutoff valve, you can turn off the water supply to the entire line running to the bath sink.
four
Drain the h2o. To remove excess water from the faucet and to relieve pressure before you beginning working, bleed the pipes later on yous close off the water. Turn on all the faucets at the sink and keep them running until all the water has tuckered out.^[3]
- This will protect your sink, vanity, and floors from leaks and water damage, and prevent water from spraying everywhere when you lot remove the faucet.
Advertisement

one
Disconnect the supply tubes. These are the tubes that connect the faucet to the water supply. Utilize the adjustable wrench to loosen the nuts where the hoses attach to the water supply. Use the basin wrench to loosen the nut attaching the hoses to the faucet. Turn the nuts to the left (counterclockwise) to loosen them.^[4]
- One time you've loosened the nuts with the wrenches, you tin remove them the rest of the way by hand.
- Wipe upwards any water that drips onto the lesser of the vanity immediately to prevent damage or warping.
two
Loosen the lock basics to take out the sometime faucet. Nearly faucets are fastened to the sink past locknuts fastened to the tailpieces under the sink.^[5] Utilise your hands or an adaptable wrench to loosen the nuts and unthread them from the tailpieces. Plow them to the left (counterclockwise) to loosen them. Remove the nuts and the washers from the tailpieces.
- Once you've removed the supply lines, nuts, and washers, the faucet will exist loose. Agree the faucet in both hands and pull it direct out from the mounting holes. Remove the gasket if in that location is one and set it aside with the faucet.
- Use the flashlight to locate the nuts under the sink if you're having trouble locating them.
3
Scrub the faucet holes. With a sponge or gentle abrasive pad, scrub the mounting holes around the sink where the faucet sits. Utilize soap and water or your favorite cleaner or detergent. Once the surface area is clean, rinse it well, pat it dry out, and let information technology air dry completely.
- To remove old sealant or silicone, dampen a sponge or rag with mineral spirits and wipe the area clean. And then rinse the area with clean water and pat information technology dry.^[6]
4
Determine what kind of faucet you lot have. Once you've removed the sometime faucet from the mounting holes, you can figure out what hole configuration yous're working with and the blazon of faucet y'all need. There are three major types of faucets:^[7]
- Unmarried hole, where the sink will only have 1 hole for the faucet, and the faucet will all be one uncomplicated piece with a single handle.
- Middle-set, where at that place will be 3 holes in the sink and the i-piece faucet will have split handles controlling the hot and cold water.
- Widespread or split-set, which work with three-hole basins, but the spout and two handles come in 3 separate pieces.
5
Purchase a new faucet. Earlier yous go to the home or hardware store for a new faucet, determine the type of faucet you have, wait at your bowl pigsty configuration, and measure the altitude betwixt the holes so that you get the correct replacement faucet. Write down the number of holes your basin has, the type of faucet that was on there, and the distance between the holes.^[8]
- If you want to replace your quondam faucet with a new kind, you'll take to replace the basin besides.
Advertisement

1
Install the gasket. The gasket is a rubber or plastic piece that sits between the faucet and the sink to ensure a proper seal and prevent leaks. Fit the gasket over the bottom of the faucet, matching the holes in the gasket with the tailpipes and valves on the faucet.
- Plastic gaskets by and large snap onto the faucet, so exist sure to seat them properly so the faucet is tightly sealed.
- If your faucet didn't come with a gasket, you'll need to apply sealant or plumber'due south putty before installing the faucet. Follow the manufacturer'due south directions and lay down a thin layer of sealant or putty right before yous put in the faucet.^[9]
ii
Wrap all the threads with plumber'southward record. Plumber'due south tape is designed to lubricate fittings and create a better seal betwixt components. Wrap the stop of the faucet tailpipes with a layer of plumber'southward record, making sure the tape doesn't extend beyond the terminate of the pipe.^[x]
- The tailpipes are where the water supply hose will attach to the faucet, and the tape volition prevent leaks.
3
Insert the new faucet. Hold the faucet in both easily and carefully set it into the mounting holes. Lucifer the tailpipes and valves with the proper holes, and identify the faucet into position.
- Once the faucet is in the mounting holes, insert a washer over each tailpipe, and and so twist on the nuts past paw. To tighten the nuts, turn them to the right (clockwise).
- When yous've tightened the nuts by hand, finish tightening them by turning them another quarter plough with the adaptable wrench if necessary.^[eleven]
- Avoid tightening the nuts any further, or you lot could damage the sink.
iv
Attach the h2o supply hoses. Start by attaching the hoses to the faucet commencement. Adhere each hose to the tailpipe of the faucet, and then tighten the nut by hand. To end tightening the nuts, use the basin wrench to turn each nut a quarter turn to the right (clockwise).
- One time the hoses are fastened to the new faucet, reattach them to the water supply. Turn the nuts past hand to the right (clockwise), then tighten them the residual of the fashion with the adjustable wrench.^[12]
- If you lot are attaching the supply lines to copper pipes with threaded fittings, hold the copper pipe deeply while connecting the supply lines to ensure the pipes don't twist or break.
5
Turn on the water and test the faucet. When everything is connected and tightened, plow the water back on by turning the shutoff valve to the left (counterclockwise). And then turn on the taps to affluent out the new faucet. When the water is running, check for leaks and drips.
- To affluent the faucet, simply let the hot and cold water run for 1 to two minutes.^[thirteen]
Advert

Add New Question

Question

The water supply nut is corroded and difficult to plough. What do y'all suggest?

Layla Moulding

Community Reply

Spray with WD40 or drib some oil around the nut, apply a flat caput screwdriver and/or a spanner or adjustable wrench.

Enquire a Question

200 characters left

Include your email address to get a bulletin when this question is answered.

Submit

Advertizement

If the faucet bolts are stripped or rusted, you can score through the silicone that holds the vanity top in identify. Remove the vanity pinnacle to allow easier admission to remove the faucet. After disconnecting the supply lines and installing the new faucet, apply clear silicone caulking effectually the edges and set the vanity top dorsum in identify. And so, reinstall the supply lines.

Thanks for submitting a tip for review!

Advertising

About This Article

Article Summary 10

Before replacing a bathroom faucet, turn off the water supply using the valve behind the sink, and bleed the pipes beneath the basin. Next, disconnect the supply tubes beneath the basin, and use a wrench to remove the bolts property the old faucet in place. Then, remove the old faucet, insert the new gasket and faucet over the existing hole, and wrap the ends of the new supply lines with plumber's record. Finally, reconnect the supply hoses and tighten each bolt with the wrench before turning the water supply back on. For advice on how to supplant a center-set faucet with a single hole faucet, read on!

Did this summary assistance you?

Thank you to all authors for creating a page that has been read 83,063 times.